Finally I got some time to continue. I sanded the Bridgetower and removed some bad spots. Then I glued the tower on his base and added the sensor array.
Endlich hatte ich mal wieder etwas Zeit weiterzumachen. Ich habe den Brückenturm geschliffen und ein paar Giesfehler repariert. Danach habe ich den Turm auf seine Basis geklebt und noch die Sensor-Antenne angebracht.
After that I primed everything. Looks good but some spots still need some work.
Danach habe ich das ganze grundiert. Sieht schon gut aus, aber ein paar stellen müssen noch überarbeitet werden.
The tower has now 11 holes for the fiber optics. Then I glued them and the next step is closing the big hole at the bottom of the tower where the fiber optics are coming out.
Der Turm hat jetzt elf Löcher für die LWLs. Danach habe ich diese angeklebt. Der nächste Schritt ist das grosse Loch, durch das die LWLs auf der Unterseite des Towers herraus kommen, zu schliessen.
Since yesterday I finished one area of the Ship I started working on the Bridge Level today. First I took all needed Parts and looked how everything fits together.
Da ich gestern einen Bereich des Shiffes fertig gestellt hatte ging es heute an die Brückenebene. Erst mal habe ich alle benötigten Teile genommen und geschaut ob alles passt.
Those three buildings on top didn’t really fit well so some cutting and sanding was needed.
Die oberen drei Aufbauten passten nicht wirklich gut, also war etwas schneiden und schmirgeln nötig.
Much better now. But as you can see the lower building didn’t really fit well. With some Milliput I was able to adjust the hight:
Viel besser. Wie man sieht passt das untere Gebäude nicht wirklich. Mit etwas Milliput konnte ich die Höhe ganz gut anpassen:
That is of course not how it will look in the end. The Putty now must dry and then it can be sanded.
Since I had a lot of Putty left I decided to do some repairs of the outer Body:
So wird es natürlich nicht endgültig aussehen. Das Putty muss jetzt aushärtern und dann kann geschmirgelt werden.
Da ich noch eine menge Putty übrig hatte, habe ich mich dann entschlossen noch ein paar Reparaturen am Rumpf zu starten:
I got some new Stuff. From left to right:
A USB-Mini-Vacuum Cleaner, Mr. Disolver Putty, Breathing Mask (to protect me from the drilling dust) and a LED Head Lamp.
Ich hab einiges an neuem Material/Werzeug bekommen. Von links nach rechts:
Ein USB-Mini Staubsauger, Mr. Disolver Putty, eine Atemschutzmaske (zum Schutz vor dem Feinstaub beim Bohren/Fräsen) und eine LED Stirnlampe.
I started hollow another Building and the Shipbody where it belongs:
Ich habe angefangen ein weiters Gebäude und die passende Stelle im Schiffsrumpf auszufräsen:
Looking good so far:
Sieht doch bisher gut aus:
Now the other side.
Nun auf zur nächsten Seite
This is how I work:
Aus meinem Blickwinkel:
While working on this Building one of my Drills broke 😦
Während ich an diesem Gebäude gearbeitet habe ist einer meiner Bohrer gebrochen 😦
But I had a spare one so I could finish this and another Building. This part of the Ship is now done.
Aber ich hatte Ersatz und so konnte ich dieses und ein weiters Gebäude fertigstellen. Somit ist dieser Teil des Schiffes fertig.
At last here a Video of me drilling a Trench:
Zu guter letzte noch ein Video wie ich einen Graben ausbohre:
After this I started with a very thin piece (the lower Building):
Danach habe ich mit einem ziemlich dünnen Teil angefangen (das untere Gebäude):
Because of the size I couldn’t the rotary cutter I’m normally using. I had to use one of my smaller drills (1.2 mm):
Aufgrund der Grösse konte ich nicht den Fräsaufsatz den ich sonst nutze nehmen. Also habe ich einen meiner kleineren Bohrer benutzt (1.2mm):
To drill a “trench” into the building itself I used a magnifier during the whole time. To visualise how small it is I place a normal lighter next to the building:
Um einen “Graben” in das Gebäude zu bohren habe ich die ganze Zeit eine Lupe benutzt. Um zu veranschaulichen wie klein das ganze ist habe ich mal ein normales Feuerzeug daneben gelegt: